Code zero, reacher or gennaker – which sail to choose for reaching

In short: a code zero is a flat sail for close reaching in light winds – usually furling. A gennaker is a fuller, asymmetric sail for broad reaching and running, set without a spinnaker pole. A reacher sits in between: it is flat like a code zero but works over a wider range of angles. The right choice depends on the gap in your yacht’s sail wardrobe.

Where the gap comes from

A jib or genoa works best upwind. A spinnaker works best downwind. In between, on a reach, a yacht often loses speed: the headsail is already too flat and too small, and the spinnaker still too deep. This is especially noticeable on modern yachts with a fractional rig and a non-overlapping jib – there such a sail is practically a must. On an older yacht with a large genoa the gap is smaller.

Code zero

  • What for: close reaching in light and moderate winds – angles that used to be covered only by large genoas.
  • Design: very flat, with a straight luff. Under racing rules (RRS, ORC) it is measured as a spinnaker, because its width at half height is at least 75% of the foot.
  • Handling: almost always furling – you set and furl it from the cockpit.
  • Remember: a code zero will not replace a genoa upwind.

Reacher

  • What for: reaching over a wider range of angles than a code zero, also in stronger winds.
  • Design: flat, with a straight luff, which makes it stable and predictable.
  • Who it suits: cruising sailors who want one versatile reaching sail.

Gennaker (asymmetric spinnaker)

  • What for: broad courses – from a beam reach to a broad reach. Flat gennakers sail higher, fuller ones deeper.
  • Design: asymmetric, made of light nylon. The tack is fixed at the bow or on a bowsprit, with no spinnaker pole.
  • Handling: easier than a symmetric spinnaker. A snuffer (sock) or a furling system makes setting and dropping simple.
  • Who it suits: the most common cruising choice for broad courses – no experienced foredeck crew needed.

Comparison at a glance

Code zeroReacherGennaker
Coursesclose reachingreaching, wide rangebeam reach to broad reach
Shapevery flatflatfuller
Windlight to moderatelight to fresherlight to moderate
Handlingfurlingfurlingsnuffer or furling
Typical yachtfractional rig, non-overlapping jibcruising, one versatile sailcruising and racing

Which one to choose

  • You have a non-overlapping jib and lack speed on a reach: a code zero or a reacher.
  • You cruise and want one sail for many courses: a reacher or a versatile gennaker.
  • You mostly sail broad courses: a gennaker – and if it is often windy, a smaller, flatter one.
  • Racing: usually a set – a code zero for tight angles and asymmetric spinnakers for broad ones. Remember that in racing these sails are measured as spinnakers and affect your rating.

FSL furling sails

We also build code zeros and reachers with FSL (Furling Structure Luff) technology: reinforcements sewn into the luff let the sail furl without a heavy anti-torsion cable. The sail is lighter and easier to handle.

How to order

We design each of these sails for a specific yacht. Download the measurement form or request a free quote – we will reply within 3 working days at the latest.

See our sails: Code Zero Cruise 55-65 (Flat Reacher) · Racing Code Zero 75 · Asymmetric Spinnaker All Purpose gennaker · Asymmetric spinnakers

Frequently asked questions

What is the difference between a code zero and a gennaker?
A code zero is flat and works on close reaches, usually on a furler. A gennaker is fuller, made for broad courses and usually set from a snuffer.

Is a code zero a spinnaker?
Under racing rules, yes – it is measured as a spinnaker because its width at half height is at least 75% of the foot. In practice it works more like a large, flat genoa.

Do I need a bowsprit for a gennaker?
Not always – the tack can be fixed at the bow. A bowsprit moves the sail forward of the forestay, so it works better and is easier to handle.

Do you have any questions, or are you unsure about something?

Contact us!

Order a Bag

Code zero, reacher or gennaker – which sail to choose for reaching – BrytSails

Thank you for your message. Our team will get back to you within 3 business days at the latest! Have a great day!